Powermatic 2000 User Manual

Browse online or download User Manual for Power tools Powermatic 2000. Powermatic 2000 User's Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 44
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
Operating Instructions and Parts Manual
10-inch Cabinet Saw
Model: 2000
Model 2000 Table Saw shown with optional extension table and legs
WMH TOOL GROUP
2420 Vantage Drive
Elgin, Illinois 60123 Part No. M-1791997
Ph.: 800-274-6848 Revision B 04/06
www.wmhtoolgroup.com Copyright © WMH Tool Group
This Manual is Bookmarked
Page view 0
1 2 3 4 5 6 ... 43 44

Summary of Contents

Page 1 - 10-inch Cabinet Saw

Operating Instructions and Parts Manual 10-inch Cabinet Saw Model: 2000 Model 2000 Table Saw shown with optional extension table and legs

Page 2 - WARRANTY AND SERVICE

10 Assembly Mounting Extension Wings Referring to Figure 1: 1. Mount a cast iron extension wing (A) to the right or left side of the table (B) using

Page 3 - Table of Contents

11 Lock Knobs and Swivel Handles Referring to Figure 4: 1. Thread the swivel handles (A) into the front and side handwheels (C) and tighten with a 14

Page 4 - Warnings

12 Blade Installation/Replacement Use care when working with or around sharp saw blade to prevent injury! To install or replace a blade (refer to Fi

Page 5

13 Riving Knife and Guard Installation Description Referring to Figure 9: The complete riving knife and guard assembly is shown in A. Before installi

Page 6 - Specifications

14 Grounding Instructions Electrical connections must be made by a qualified electrician in compliance with all relevant codes. This machine must be

Page 7 - Shipping Contents

15 Castor system adjustment Retractable castors can be extended permitting the saw to be moved: 1. Loosen the lock knob (A) on the side handwheel (C)

Page 8

16 Miter Slot Alignment Disconnect machine from power source before making this adjustment. To check the alignment of the miter slot to the blade: 1

Page 9

17 Precision Miter Gauge Setting the miter gauge angle Referring to Figure 15: The precision miter gauge has a rack and pinion adjustment for setting

Page 10 - Assembly

18 Riving Knife Adjustment Lateral alignment The saw blade and riving knife must be in line as close as possible with each other (lateral alignment)

Page 11 - Dust Chute

19 Note: These screws are accessible through openings on the floating clamp block (B) located diagonally on either side of the lock handle (A). They

Page 12

2WARRANTY AND SERVICE WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Servi

Page 13

20 Operating Controls Start/Stop Power Indicator Light – The start switch has a power indicator lamp which is on whenever there is power connected t

Page 14 - Adjustments

21 Operations Overview Familiarize yourself with the location and operation of all controls and adjustments and the use of accessories such as the mi

Page 15 - Zero-Clearance Insert Setup

22 Rip Sawing Ripping is where the work piece is fed with the grain into the saw blade using the fence as a guide and a positioning device to ensure

Page 16 - Tilt Stop Adjustment

23 When ripping long boards, use a support at the front of the table, such as a roller stand, and a support or "tailman" at the rear as sho

Page 17 - Precision Miter Gauge

24 Bevel and Miter Operations Bevel Cut – A bevel cut is a special type of operation where the saw blade is tilted at an angle less than 90 degrees t

Page 18 - Riving Knife Adjustment

25 Safety Devices Feather Board and Push Blocks A feather board or push block is not provided but can be purchased by calling customer service at the

Page 19 - Insert Adjustment

26 Maintenance Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious personal injury. Clean

Page 20 - Operating Controls

27 Troubleshooting Trouble Probable Cause Remedy Tilt or raising clamp knobs not tightened. Tighten knobs. Blade out of balance. Change blade. [pag

Page 21 - Operations

28 Optional Accessories 2195042K Accu-Fence and rail system for ripping 50" to right and 12" to left of saw blade. 2195079Z Accu-Fence -

Page 22 - Rip Sawing

29 Model 2000 Table Saw Parts List Table & Cabinet Assembly Index No. Part No. Description Size Qty 1 ...PM2000-101 ...B

Page 23 - Crosscutting

3Table of Contents WARRANTY AND SERVICE ...

Page 24 - Bevel and Miter Operations

30 Table & Cabinet Parts Assembly

Page 25 - Safety Devices

31 Trunnion & Motor Assembly Parts List Index No. Part No. Description Size Qty 1 ...PM2000-201 ...Knob...

Page 26 - Maintenance

32 Trunnion & Motor Assembly Parts List Index No. Part No. Description Size Qty ...PM2000-JBC...Junction Box Cover (no

Page 27 - Troubleshooting

33 Trunnion & Motor Assembly Parts List Index No. Part No. Description Size Qty 88 ... PM2000-288 ...DU Bushing...

Page 28 - Optional Accessories

34 Trunnion & Motor Assembly

Page 29 - Table & Cabinet Assembly

35 Blade Guard & Miter Gauge Assembly Parts List Index No. Part No. Description Size Qty 1 ...PM2000-301 ...Riving Knife

Page 30

36 Blade Guard & Miter Gauge Assembly

Page 31

37 Side Cover Assembly Index No. Part No. Description Size Qty ...6827044 ...PM2000 Motor Cover Assembly (Index #1

Page 32

38 Wiring Diagrams 3HP, 230V, 1Phase 5L3A13L213NO1L22T14T26T314NO2T14T26T3A2GROUNDGREENGREENBLACKWHIET959698 97450VAC20UFGREENBLACKWHITE250VAC250MF

Page 33

39 5HP, 230V, 1Phase 5L3A13L213NO1L22T14T26T314NO2T14T26T3A2GROUNDGREENGREENBLACKWHIET959698 97450VAC35UFGREENBLACKWHITE250VAC400MFDWHITEBLACKWHITEB

Page 34

4 Warnings 1. Read and understand the entire owners manual before attempting assembly or operation. 2. Read and understand the warnings posted on t

Page 35

40 5HP, 230V, 3Phase BLACKREDYELLOWBLACKWHITEGREENMagnetic SwitchElectrical BoardMotorREDREDZ1Y1X1U2V2W2W1V1 U1REDREDRCYELLOWWHITEREDLED2T14T26T3A2G

Page 36

41 5HP, 460V, 3Phase BLACKREDYELLOWBLACKWHITEGREENMagnetic SwitchElectrical BoardMotorREDREDZ1Y1X1U2V2W2W1V1 U1REDREDRCYELLOWWHITEREDLED2T14T26T3A2G

Page 39

44 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.com

Page 40

5 17. Provide for adequate space surrounding work area and non-glare, overhead lighting. 18. Keep the floor around the machine clean and free of s

Page 41

6Introduction This manual is provided by WMH Tool Group covering the safe operation and maintenance procedures for a Powermatic Model 2000 Table Saw.

Page 42

7Shipping Contents Unpacking Remove box and wood crating completely from around saw. Check for shipping damage. Report any damage immediately to your

Page 43

8 Contents of the Shipping Container Main Saw Container 1 Table Saw (A) 1 Table Insert (B) The following items are inside the saw: 1 Miter G

Page 44 - Phone: 800-274-6848

9 Extension Tables Two extension tables are packaged in individual boxes. Extension Tables Side Cover Box 2 Hinge Pin (N) 1 Side Cover (O)

Comments to this Manuals

No comments