Powermatic PM1300 User Manual download pdf (Page 8)

Base Machine Assembly

The dust collector must not be

connected to the power source

during assembly. Failure to comply may result

in serious injury!

All instructions on this page refer to Figure 3.

Base and Casters

1. The 3/8” hex nut (F) and M10 lock washer

(G) are pre-assembled to each caster (J). For

shipping purposes, the lock washer has been

placed beneath the hex nut. Remove hex nut

and lock washer from the caster shaft, re-

install the hex nut, then install the lock

washer above the hex nut, as shown.

2. Install the four casters (J) to the underside of

the base (H) as follows:

3. Thread the caster shaft into the threaded hole

on the underside of the base (H), turn until

snug. Tighten the hex nut (F) against the

base with a 14mm wrench.

Motor and Fan Assembly

1. Place the base with casters down on the

ground.

2. Attach the motor and fan assembly (K) to the

base (H) using six M8x20 hex cap screws (A),

and six M10 flat washers (D). Hand tighten only

until all screws and washers are in place, then

adjust the motor and fan assembly (K) until its

flanges are approximately flush with the edges

of the base (H). Tighten all screws with a 13mm

wrench.

3. Attach the inlet guard (L) to fan housing (K)

using eight M6x12 pan head flange screws (B).

4. Press the inlet port (M) as far as it will go onto

the inlet guard (L).

To reduce the risk of injury from

moving parts, always keep both holes of inlet

port (M) covered with either the provided cap or

dust hoses. Failure to comply may result in

serious injury!

Connector Tube and Switch Box

1. Place the lower gasket (N) on the fan housing

(K). Line up the rubber pegs on the gasket

(face down) with the holes in the housing.

2. Place the connector tube (O) on the fan

housing (K), making sure that the holes of the

mating flanges are aligned.

Note: Refer to Figure 3 to make sure that the

connector tube is facing the proper direction.

3. Insert an M8x20 hex cap screw (A), through the

M8 washer (C) and flanges of the connector

tube (O) and fan housing (K).

4. Place another washer (C) and a hex nut (E) on

the protruding end of the screw (A) and hand-

tighten only.

5. Mount the control box (P) to the two holes at

the front of the connector tube flange.

6. Repeat steps 3 and 4 for the remaining screw

locations, hand tightening only.

7. Tighten all hex nuts with a 13mm wrench.

Collector Housing

Mount the collector housing (S) as follows:

1. Place an upper gasket (R) between the

collector housing (S) and connector tube (O).

Line up the pegs on the gasket (R) with the

holes in the housing (S).

2. Place the collector housing (S) on the

connector tube (O).

3. Insert a screw (A) through the washer (C),

connector tube flange (O), and collector-

housing flange (S).

4. Place another washer (C) and a hex nut (E) on

the protruding end of the screw (A) and hand-

tighten.

5. Repeat steps 1 through 4 for the seven

remaining screw locations.

6. Tighten all hex nuts with a 13mm wrench.

Support Bar

1. Align the bottom slots of the support bar (T)

with the holes in the base (H). Insert two

screws (A) and two flat washers (C) and hand

tighten only.

Note: If you are using the Canister Filter

System, proceed with steps 2 through 4

below. If you are using the Filter Bag System,

leave the support bar (T) as is, for further

assembly later, and proceed to “Handles”.

2. Align the top holes of the support bar (T) with

the holes at the rear of the collector housing

(S) and insert two screws (A) and two flat

washers (C).

3. Place a washer (C) and a hex nut (E) on the

protruding end of each screw (A) inside the

collector housing, and hand-tighten only.

4. Adjust the lower part of the support bar (T) as

needed using its slots, until it is straight. Then

tighten all four screws on the support bar (T).

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 23 24

Comments to this Manuals

No comments

Powermatic PM1300 User Manual Page 8

Comments to this Manuals