Powermatic PM2000 User Manual

Instructions and Parts Manual 10-inch Cabinet Saw Model PM2000 Model PM2000 Table Saw shown with optional extension table and legs WAL

10 Assembly Mounting Extension Wings Referring to Figure 1: 1. Mount a cast iron extension wing (A) to the right or left side of the table (B) using

11 Lock Knobs and Swivel Handles Referring to Figure 4: 1. Thread the swivel handles (A) into the front and side handwheels (C) and tighten with a 14

12 Blade Installation/Replacement Use care when working with or around sharp saw blade to prevent injury! To install or replace a blade (refer to Fi

13 Riving Knife and Guard Installation Description Referring to Figure 9: The complete riving knife and guard assembly is shown in A. Before installi

14 Grounding Instructions Electrical connections must be made by a qualified electrician in compliance with all relevant codes. This machine must be

15 Castor system adjustment Retractable castors can be extended permitting the saw to be moved: 1. Loosen the lock knob (A) on the side handwheel (C)

16 Miter Slot Alignment Disconnect machine from power source before making this adjustment. To check the alignment of the miter slot to the blade: 1

17 Precision Miter Gauge Setting the miter gauge angle Referring to Figure 15: The precision miter gauge has a rack and pinion adjustment for setting

18 Riving Knife Adjustment Lateral alignment The saw blade and riving knife must be in line as close as possible with each other (lateral alignment)

19 Note: These screws are accessible through openings on the floating clamp block (B) located diagonally on either side of the lock handle (A). They

2 Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Au

20 Operating Controls Start/Stop Power Indicator Light – The start switch has a power indicator lamp which is on whenever there is power connected to

21 Operations Overview Familiarize yourself with the location and operation of all controls and adjustments and the use of accessories such as the mi

22 Rip Sawing Ripping is where the work piece is fed with the grain into the saw blade using the fence as a guide and a positioning device to ensure

23 When ripping long boards, use a support at the front of the table, such as a roller stand, and a support or "tailman" at the rear as sho

24 Bevel and Miter Operations Bevel Cut – A bevel cut is a special type of operation where the saw blade is tilted at an angle less than 90 degrees t

25 Safety Devices Feather Board and Push Blocks Feather boards and push blocks can be purchased at most woodworking stores that sell table saws and a

26 Maintenance Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious personal injury. Clean

27 Troubleshooting Trouble Probable Cause Remedy Excessive vibration. Tilt or raising clamp knobs not tightened. Tighten knobs. Blade out of balance

28 Optional Accessories 2195042K Accu-Fence® and rail system for ripping 50" to right and 12" to left of saw blade. 2195079Z Accu-Fence® -

29 Model PM2000 Table Saw Parts List Side Cover Assembly Index No. Part No. Description Size Qty ... 6827044 ...PM200

3 Table of Contents Warranty and Service...

30 Table & Cabinet Assembly Index No. Part No. Description Size Qty 1 ... PM2000-101...Base ...

31 Table & Cabinet Assembly

32 Trunnion & Motor Assembly Parts List Index No. Part No. Description Size Qty 1 ... PM2000-201...Knob ...

33 Trunnion & Motor Assembly Parts List Index No. Part No. Description Size Qty ... PM2000-JBC ...Junction Box Cover (no

34 Trunnion & Motor Assembly Parts List Index No. Part No. Description Size Qty 88 ... PM2000-288...D U Bus hi ng ...

35 Trunnion & Motor Assembly

36 Blade Guard & Miter Gauge Assembly Parts List Index No. Part No. Description Size Qty 1 ... PM2000-301...Riving Knife

37 Blade Guard & Miter Gauge Assembly

38 Wiring Diagrams 3HP, 230V, 1Phase 5L3A13L213NO1L22T14T26T314NO2T14T26T3A2GROUNDGREENGREENBLACKWHIET959698 97450VAC20UFGREENBLACKWHITE250VAC250MFD

39 5HP, 230V, 1Phase 5L3A13L213NO1L22T14T26T314NO2T14T26T3A2GROUNDGREENGREENBLACKWHIET959698 97450VAC35UFGREENBLACKWHITE250VAC400MFDWHITEBLACKWHITEB

4 Warnings 1. Read and understand the entire owner’s manual before attempting assembly or operation. 2. Read and understand the warnings posted on

40 5HP, 230V, 3Phase 5L3A13L213NO1L22T14T26T314NO2T14T26T3A2GROUNDGREENGREENBLACKWHIET959698 97GREENBLACKWHITEWHITEBLACKWHITEBLACKGREENBLACKREDYEL L

41 5HP, 460V, 3Phase 5L3A13L213NO1L22T14T26T314NO2T14T26T3A2GROUNDGREENGREENBLACKWHIET959698 97GREENBLACKWHITEWHITEBLACKWHITEBLACKGREENBLACKREDYELLO

42 Notes

43

44 WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.powermatic.com w

5 17. Provide for adequate space surrounding work area and non-glare, overhead lighting. 18. Keep the floor around the machine clean and free of sc

6 Introduction This manual is provided by Walter Meier (Manufacturing) Inc., covering the safe operation and maintenance procedures for a Powermatic

7 Shipping Contents Unpacking Remove box and wood crating completely from around saw. Check for shipping damage. Report any damage immediately to you

8 Contents of the Shipping Container Main Saw Container 1 Table Saw (A) 1 Table Insert (B) The following items are inside the saw: 1 Miter G

9 Extension Tables Two extension tables are packaged in individual boxes. Extension Tables Side Cover Box 2 Hinge Pin (N) 1 Side Cover (O)